Satisfaction guaranteed. Call us anytime: 1-877-880-TILE (8453).
Cart: 0 items, $0.00

Your shopping cart is empty.


ATR Leveling System Questions and Answers

October 20, 2012

ATR Leveling System, Tile leveling, lippage free, wedges, atr plastic, spacers, flat surfaces, RTC Tornado Leveling System, Tuscan Leveling System, Raimondi Leveling

Questions and Answers

Q. What are the advantages of using the Tile Levelers?

A. It is quick and easy to use, provides an accurate smooth finish and has been proven to decrease installation time.

Q. Why ATR system and no other? What the different?

A. ATR stand up to all other Leveling System in the market look at his COMPARISON CHART the amount of spacers needed by ATR are about 30% of all other leveling system, that mean lower cost of material and a greater saving on installing, removing can carrying additional 70% of spacers

Q. Can the Spindle be reused?

A. Yes, the spindle is reusable and recyclable.

Q. Does the Tile Levelers eliminate lippage?

A. The Tile Levelers will eliminate any lippage under circumstances where the floor or wall coverage area is reasonably level.

Q. How much faster is the tile leveling process using the ATR system?

A. Feedback from installers in large and confined areas say it has increased their productivity in their sq ft laying time by 20 to 35 percent.

Q. Can the Tile Levelers be used with any tile?

A. The Tile Levelers is designed to work with any size tile with a thickness of between apex 1/4″ to 3/4″ exact 6mm and 20mm.

Q. What type of tile can the Tile Levelers be used on?

A. The Tile Levelers will work with ceramic, porcelain, marble, onyx, granite and most composites.

Q. Can the ATR Tile Levelers be used on walls?

A. Yes, the Tile Levelers can be used on walls.

Q. What is the learning curve using the Tile Levelers?

A. It is a very simple procedure which only takes minutes to learn.

Q. Can a cordless drill be used to install and remove the spindle?

A. Yes, we recommend using a cordless drill with voltage no greater than 10.8 volts, its clutch mechanism set to low to prevent any over tightening and a 10mm double hexagon metric socket.

How to use 5 Easy steps

1. Screw spindle into spacing plate until screw tip is just visible at underside of plate.

2. Insert Tile Levelers spindle with spacing plate attached in between two tiles.

3. Lay adjacent tiles until all four corners, or two corners for the edge spacing plate are met.

4. Tighten spindle clock wise firmly until all four corners are lifted flush.

5. Remove spindle once tile adhesive is dry.

Click Here to watch ATR Video’s

ATR Leveling System Comparison Chart

The post ATR Leveling System Questions and Answers first appeared on Flooring Supply Shop Blog.

One thought on “ATR Leveling System Questions and Answers

  1. Magnificent items from you, man. I have take into account your stuff prior to
    and you’re simply extremely magnificent. I actually like what
    you’ve got right here, certainly like what you’re saying and the way in which during which you say it.
    You’re making it entertaining and you continue to care for to keep it wise.
    I cant wait to read much more from you. This is really a wonderful web site.

  2. In reply to Jeff S..

    you should have a clean (no mortar) line in the area where tile stopped.

    you can use the Edge spacer an inch or so inside the and the following day you start your new tile just like starting the first day.

    when starting new day you start with making sure the old and new part are aligning once you do you good to go

  3. ATR leveling question. How do I stop laying tile for the day (large 680 sf project) and return the next day? Do I dig out the area (mortar) where the spacers are on the edge of the tiles where I will continue the next day? Then do I place the spacers in the area where I removed the mortar before I leave for the day?

  4. How think are the spacers ? i read that i can use the system with underfloor heating. The wire of my floor heating system appears to be 3mm (1/8) but maybe as much as 5/32. Can i still use the 3mm product and expect the tile level to be above the wire or would the heating wire hold the base above the subfloor?

  5. In reply to Jim.

    Can these be used with tile spacers so I can use the proper grout size according to the manufacturer’s specs?

    Yes you can but you will not going to get the spacers future of the Cross or T spacer and you need to make sure your tile are in straight line, one of the advantages of the ATR on other leveling system we carry is that the spacing plates lock the tile into position giving you the most perfect intersection of the tile and straight lines without requiring consistent adjustments

    can I purchase just edge spacers since I would need more edge spacers than corner spacers on an elaborate installation like a pinwheel pattern?

    Yes you can buy individual boxes of any type or size or Kits

  6. Can these be used with tile spacers so I can use the proper grout size according to the manufacturer’s specs? Also, can I purchase just edge spacers since I would need more edge spacers than corner spacers on an elaborate installation like a pinwheel pattern?

  7. Hi, it says that the 3mm spaces for floor only. Why is this? why can’t I use the 3mm spacers for a wall tile job (that is using 12×24 tiles)?

  8. Hi, I am interested in using this product. I want to verify this product can be used with electrical radiant floor heating. The wires are spaced every 2 inches and I am concerned that the clip that is put underneath the tile will melt. This could cause all kinds of problems including melted plastic, shrinkage where the clips are, etc. Can you please verify if the ATR leveling system can be used with electric radiant heat. Thanks

  9. In reply to victor escobar.

    hola no entiendo bien los precios me podria decir cuanto cuesta el espaciador de 2mm y el husillo le agradeceria por unidad

    (Translate) hello prices do not quite understand how much it costs I could say 2mm spacer and spindle unit would appreciate

    The prices are clearly on our web site

    Cross spacers are 150/pack for $49.99
    Edge Spacers are 100/pack for 25.99
    Spindles are 100/pack for 54.99

  10. Hi, I am a novice tiler and am looking to purchase your ATR system and the Bosch GTL3 tile laser. Can you advise whether the ATR spindles are likely to obstruct the laser line? I have been in contact with Bosch and they don’t think so but both systems are a sizeable investment and Would appreciate your thoughts.

Leave a Reply

Your email address will not be published. Required fields are marked *

Chat with us Chat