Miracle 511 Impregnator Sealer
511 Impregnator Sealer
by Miracle Sealants Company
This product is formulated for sealing concrete and masonry to provide resistance against water, alkalis, acids, ultraviolet light, stain-ing, salt ion intrusion and freeze/thaw damage.
511 Impregnators a unique poly-merized silicone formulation designed for the protection of all medium to dense porous tile, stone and grout surfaces. 511 Impregnator penetrates into the surface and forms an invisible barrier that is resistant to moisture and stains, while allowing vapor to escape. 511 Impregnator is not a surface coating and will not alter the nature-al look. All surfaces are harder and less slippery.
511 Impregnator can be used on interior and exterior applications. 511 Impregnator is U.V. transparent, resists acid rain and will not yellow under any circumstances. 511 Impregnator averages five to twenty times the coverage of competitive products. (See coverage chart). 511 has been formulated for or applied to freshly poured concrete to retard the evaporation of water.
511 Impregnator is on the approved sources list of the United States Postal Service and is U.S.D.A. approved for incidental food contact in federal meat and poultry establishments.
• Interior & Exterior • Kitchen
• Showers • Restrooms
• Patios • Drive Ways
Water, Stain & Slip Protection for
• Quarry Tile • Ceramic Tile • Porcelain Tile
• Glazed Tile • Marble • Granite
• Travertine • Medium -Dense Slate • Grout
• Quartz • Medium -Dense Brick • Terrazzo
NEW INSTALLATIONS - APPLICATION INSTRUCTIONS
Read entire label and PDS/MSDS before using. 511 Impregnator should not be
diluted or thinned in any way. 511 Impregnator should be used as is direct from
Before Grouting: Apply 511 Impregnator to all surfaces prior to grouting. This step will allow quick and easy cleanup after grouting. Grout can stain many surfaces if this procedure is not used prior to the grouting process.
Apply 511 Impregnator using a Mira Brush or a clean towel. Apply enough to wet the surface. (See coverage charts) Be careful not to saturate the open grout joints. Allow 511 Impregnator to stand for approximately 3 - 5 minutes for maximum penetration. All excess must be removed at this time by buffing surface with a clean dry towel. This is very important on polished, glazed and porcelain surfaces. Allow 511 Impregnator to cure for 12 - 24 hours before continuing with the grouting procedure.
After Grouting: Once grouted, make sure that all grout residue is removed from the surface with a clean sponge and water. Allow grout to cure per manufacturers specification. If grout clean up is not performed effectively, an additional cleaning may be necessary to remove remaining grout residue or haze. For this procedure use Phosphoric Acid Cleaner , (GCFR) Grout & Concrete Film Remover (Hydrochloric Acid), Sulfamic Acid Crystals or Epoxy Grout Film Remover following the instructions carefully. Once the area has completely dried, proceed with the sealing of the grout for water and stain resistance.
Apply 511 Impregnator to all grout with a paint brush. Any excess sealer that gets on the surface should be wiped off with a clean towel before it dries. On larger jobs grout can be sealed by retreating the entire area including he tile or stone surface a second time.
Be careful not to allow the sealer to puddle or dry on pre sealed surfaces.
Existing Installation - Surface Preparation
Surface must be dry and free of contaminants, including previously applied sealers,
dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime.
Surface Coating/Wax Removal: To remove existing coatings and/or waxes, use Mira
Strip or H2O Strip as directed.
Heavy Duty Cleaning: To remove lime and hard water deposits, efflorescence, rust, grease and other heavy dirt and grime use GCFR (Grout & Concrete Film Remover) Phosphoric Acid Cleaner as directed. For a non acid deep clean use Liquid Poultice as directed.
Light Cleaning: Use Mira Clean #1, Porcelain & Ceramic Tile Cleaner, Tile & Grout Cleaner, Mira Soap, Counter Kleen as directed.
Existing Installation - Application Instructions
Follow the application instructions previously mentioned, except now, seal the grout and tile or stone surfaces at the same time. When treating surfaces together, make sure that the recessed grout is saturated.
Mold, Mildew and Bacteria Sanitation
For best results in killing mold, mildew, bacteria and other micro organisms, use Miracle Disinfectant as directed.
To remove accumulated 511 Impregnator residue, use Miracle Residue Remover as directed.
Color and Gloss Enhancement
For color & gloss enhancement, use Mira Matte or Mira Shine as directed.
• Easy-to-Use • Weather Resistant • Low Toxicity
• Salt Resistant • Non Coating • Freeze/Thaw Resistant
• Acid Resistant • Non Yellowing • Stain Resistant
• Slip Resistant • U.V. Transparent • Water Resistant
511 Impregnator Sealer is packaged in 4 - 1/4 gallon cans and 1/4 gallon.
For ongoing maintenance instructions please refer to Miracle Sealants Care Guide.
Refer to the Miracle Sealants Product Recommendation Chart for specific product recommendations.
511 Impregnator will be dry to the touch in 1 - 3 hours and may be used for normal foot traffic. For optimum results the area should be kept dry and free from staining materials for 72 hours.
Instructions are a condensed guide and should not be considered complete.
In the event of failure, the only obligation of Miracle Sealants Company shall be to replace such products proven to be defective.
Before using, user shall determine the suitability of the product for their intended use.
User assumes all risks and liability whatsoever in connection therein. Neither seller nor manufacturer shall be liable for any injury or inability to use this product.
KEEP OUT OF REACH OF CHILDREN
Glaze N Seal Wet Look 2000 - Glaze N Seal Wet Look II - Miracle 511 Impregnator Sealer - Glaze N Seal Multi Purpose Sealer - Stone Defender Aerosol Grout Sealer - Glaze n Seal Stone Color Enhancer and Seal
Cleaning and Care links
Anti Slip Links