ProMelt Snow Melting - Cable Ties

Quantity - 100

6 inch cable ties are used to tie ProMelt Mat or Cable to rewire or rebar

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting CableStrap

Size: 25 Liner Feet

Coverage Area: apex 40 - 50 Square Feet

CableStrap is used to hold ProMelt Cable in place at the desired spacing in applications that don't use rebar or rewire.
Anchor the strap at 3 - 4 ft. intervals across the surface.

Cut using ordinary tin snips.

Order one 25 ft. long coil per 50 - 60 sq. ft. of ProMelt area.

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting Heating Wire Repair Kit

Kit Include: 1. Ground jumper wire 2. ground solder tubs 4. heating wire solder tubes and 1. shring sleeve.

This simple and safe kit is used to repair heating element that have been damaged during installation.

It suitable for all ProMelt snow melting products,

Instruction are included and at the installation manual link at the bottom.

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting Extra Power Lead

Price per ft. 120 / 240 Volt

ProMelt Mats and Cables come standard with a 20 ft long power lead, but can be orderd with extra long power leads up to a maximum of 50 ft in. length

When you place your order, let us know how long the leads need to be in order to reach the electrical box or control.

We'll attach custom power lead to fit your application

Alternate pricing available - Contact us for pricing.

Toll free 877 880 8453 or Email contact@flooringsupplyshop.com

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting Plaque

Permanent plaque to indicate where a snow melting system has been installed

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting Contactor Pro Expansion CP-200EX - 200 Amp

The contactor Pro panels are complete "turn-key" solutions for activating larger system of ProMelt Mats and Cables when used in combination with PM-224, PM-824 or PM-HSC5 snow detector.

They're available in three panel sizes 50 Amps, 100 Amps, and 200 Amps, An additional 200-amp extension panel allows coverage for even larger system.

120V, 208V, 240V or 270Volt is supplied to the panel and a 24V Class 2 transformer allows connection to the snow detector.

Each Contactor Pro panel is complete with "system on" indicator light, manual override by a 4-hr timer, simple 24V wire terminal connection to the snow detector, and outputs for connection to an extension panel.
The CP-200 has four 50-amp contactors.

Systems should be designed to connect one or more ProMelt cables or Mats in combination not to exceed the capacity of individual 50-amp contactors.

Each panel is NEMA Type 1 for mounting indoors on a wall, has knock bouts for conduit, and measures 12" x 12" 4"

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting Contactor Pro Expansion CP-200

The contactor Pro panels are complete "turn-key" solutions for activating larger system of ProMelt Mats and Cables when used in combination with PM-224, PM-824 or PM-HSC5 snow detector.

They're available in three panel sizes 50 Amps, 100 Amps, and 200 Amps, An additional 200-amp extension panel allows coverage for even larger system.

120V, 208V, 240V or 270Volt is supplied to the panel and a 24V Class 2 transformer allows connection to the snow detector.

Each Contactor Pro panel is complete with "system on" indicator light, manual override by a 4-hr timer, simple 24V wire terminal connection to the snow detector, and outputs for connection to an extension panel.
The CP-200 has four 50-amp contactors.

Systems should be designed to connect one or more ProMelt cables or Mats in combination not to exceed the capacity of individual 50-amp contactors.

Each panel is NEMA Type 1 for mounting indoors on a wall, has knock bouts for conduit, and measures 12" x 12" x 4"

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting Contactor Pro Expansion CP-100 - 200 Amp

The contactor Pro panels are complete "turn-key" solutions for activating larger system of ProMelt Mats and Cables when used in combination with PM-224, PM-824 or PM-HXC5 snow detector.

They're available in three panel sizes 50 Amps, 100 Amps, and 200 Amps, An additional 200-amp extension panel allows coverage for even larger system.

120V, 208V, 240V or 270Volt is supplied to the panel and a 24V Class 2 transformer allows connection to the snow detector.

Each Contactor Pro panel is complete with "system on" indicator light, manual override by a 4-hr timer, simple 24V wire terminal connection to the snow detector, and outputs for connection to an extension panel.
The CP-200 has four 50-amp contactors.

Systems should be designed to connect one or more ProMelt cables or Mats in combination not to exceed the capacity of individual 50-amp contactors.

Each panel is NEMA Type 1 for mounting indoors on a wall, has knock bouts for conduit, and measures 12" x 12" 4"

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

ProMelt Snow Melting Contactor Pro Expansion CP-50 - 50 Amp

The contactor Pro panels are complete "turn-key" solutions for activating larger system of ProMelt Mats and Cables when used in combination with PM-224, PM-824 or PM-HSC5 snow detector.

They're available in three panel sizes 50 Amps, 100 Amps, and 200 Amps, An additional 200-amp extension panel allows coverage for even larger system.

120V, 208V, 240V or 270Volt is supplied to the panel and a 24V Class 2 transformer allows connection to the snow detector.

Each Contactor Pro panel is complete with "system on" indicator light, manual override by a 4-hr timer, simple 24V wire terminal connection to the snow detector, and outputs for connection to an extension panel.
The CP-200 has four 50-amp contactors.

Systems should be designed to connect one or more ProMelt cables or Mats in combination not to exceed the capacity of individual 50-amp contactors.

Each panel is NEMA Type 1 for mounting indoors on a wall, has knock bouts for conduit, and measures 12" x 12" x 4"

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

PM-HSC5 Slab Detector

PM HSC5 Slab-mounted Snow melting Detector a simple and economical snow switch for mounting a snow melt slab.

This PM HSC5 Snow melting Slab Detector is pavement mounted and senses actual pavement conditions.
Microprocessor control effectively eliminates ice bridging, eliminating the need for a separate temperature sensor.
The PM HSC5 starts snow/ice melting at temperatures below 38°F (3.3°C) when precipitation is present. When the moisture element has dried, the PM HSC5 sensor continues to operate the systems for a fixed time of 6 hours.
The PM HSC5 provides a low-amperage output relay contact.
The heavy-duty machined brass housing provides optimum protection and reliability in severe service while providing an attractive appearance. The removable top cover and plug-in electronic assembly permit repair without disturbing the pavement

Place your order before 4:00 pm, (PST) and we get it out same day

SunTouch ProMelt Installation Manual

SunTouch 25 years Warranty

PM 824 Rain amd Snow Sensor Controller

The PM-824 is an advanced low voltage version of the DS-8. It is primarily designed for hydronic and low voltage gutter, downspout, and roof ice melting applications. It can also be used on existing buildings where retrofitting high voltage wiring would be to difficult. The 24VAC/VDC supply means less expensive wiring, no requirement for conduit, and lower installation costs

• Designed for Low Voltage Hydronic and Battery Powered Systems
• Automatic Activation means Lower Deicing Costs
• Reliable Rain and Snow Detection
• 24VAC/VDC Operation, Only 20 VA Required
• Full 30A @ 24VAC Control
• Replaceable Remote Precipitation Sensor
• Easy Installation, Full Access to Electronics
• 8 Different Functions, 1 Part Number
• Adjustable Temperature Trigger Point
• Adjustable Delay Off Cycle, Selectable 30-90 Minutes or 2-6 Hrs
• Exclusive Adjustable Sensitivity Control
• Selectable Low Temperature Cutoff
• Smart "Manual On" Operates for One Delay Off Cycle
• High Power, Low Price!

The unit is housed in a two gang PVC enclosure. The overall dimensions of the PM-824 are 4¾"(120) x 7"(178) x 2¾"(70). The unit weighs 2 pounds. The user may access all electronics by removing the four front cover screws. The remote precipitation sensor includes 10 feet (3 m) of interconnect cable. A weatherproof LED indicator on the base of the unit provides a method of checking power and trigger status when the unit is mounted in a "hard to reach" location. Steady OFF indicates no power to the unit. Steady ON indicates power is being supplied but no snow or rain trigger is active. A blinking LED indicates the DS-824 is triggered and connected equipment has been activated.

Wiring is performed by terminating your existing wiring to the pre-installed pigtails. The DS-824 is mounted by either attaching the mounting hub to a rigid ½" or ¾" conduit or by installing screws through the four mounting tabs provided.

The PM-824 can be powered from a 22-28VAC/VDC source. Peak power consumption is 15 VA at startup, 8.5 VA steady state triggered, 5 VA steady state un triggered. Power input is polarity protected for a DC supply. The unit provides a single 24VAC/30A or 24VDC/20A normally open load contact set. This contact set is paralleled with a low power contact set to provide remote control and activation monitoring. Operational temperature range is -40oC to +85oC.

The table below outlines the operating modes for the PM-824. Trigger Temperature (TT) is adjustable from 34oF-44oF using an on-board control. When ambient air temperature (AT) is below this trigger point precipitation is assumed to be snow or freezing rain. When above the trigger point, precipitation is assumed to be rain.

"Delay Off" refers to the internal drying cycle timer of the PM-824. The timer is used to allow the PM-824 to dry the heated surface through evaporation once precipitation has stopped. The drying cycle reduces the chance that moisture left behind by the melting process will refreeze into ice. This timer is restarted by each precipitation detection. Therefore, the PM-824 will continue to operate as long as precipitation and trigger temperature is detected, then for the "Delay Off" time once rain or snow stops. It is assumed that, when operating as a sensor, the PM-824 is supplying an activation signal to an external control system. All "sensor" modes provide a minimum 2 minute closure, reducing cycling of the external controller. The Delay Off cycle has been extended for hydronic applications and is determined by the Long Delay (LD) switch setting, DEL switch setting and the DEL adjustment. Delay Off is 30-90 minutes in non-LD "controller" mode and 2-6 hours in LD "controller" mode.

An environmentally sealed control switch is provided. The "Manual On" function activates the controlled equipment for testing and special operational conditions. The "Automatic" position allows the PM-824 to handle all detections and control. The "Standby/Reset" position disables triggering and can also be used to clear the delay off timer (see below) from true or test activation. If the switch is placed in "Manual On" for less than 2 seconds, then switched back to "Automatic" the controller will execute one delay off cycle. This allows a controlled manual activation of the snow melt system without the fear of forgetting and leaving the system in "Manual On" for an extended and potentially very expensive period of time. "Standby/Reset" can still be used to clear this delay off cycle. Remote control and monitor up to 1000 feet away is also available when the optional CS-1 C/M cable listed is installed. The PM-824 is also compatible with the DP-7B, DP-7EX, and CDP-2 remote control/status panels.

The Low Temperature Cutoff (LTC) option is typically used on deicing or snow melting systems with limited output capacity. If selected, the sensor will not trigger if precipitation is detected below 15oF. However, if the deicing system has been activated, precipitation continues, and the ambient temperature drops below 15oF, LTC will be ignored. This assures that water left behind on the surface during the heating cycle will not immediately refreeze into ice as a result of deactivating the deicing system.

The PM-824 also features a new innovation, a Trigger Sensitivity Adjustment. Previous units have always detected and triggered on the first drop of rain, the first flake of snow. While this has always provided a highly reliable detection it may create "nuisance" triggers in some installations. Snow blowing off a roof or falling from a tree could cause the system to activate for a delay cycle when its not needed, increasing operating costs. The sensitivity adjustment allows setting the number of seconds the precipitation grid must see continuous rain or snow before the sensor is triggered and ranges from 3 seconds to 4 minutes. A higher sensitivity setting assures quick detection no matter the conditions. A lower sensitivity setting will allow a few stray drips of rain or flakes of snow to be ignored but a heavier downfall will trigger the system.

Place your order before 4:00 pm, (PST) and we get it out same day

ProMelt PM-824 Spec & Installation Guide

SunTouch 25 years Warranty

PM-DP Snow Sensor Control and Display Panel

The CDP-2 brings control and monitoring of your snow melt system indoors. No need to hope that the system has successfully triggered. One glance at the CDP-2 confirms it! The CDP-2 is compatible with the DS-2B, DS-224, DS-5, and DS-8 rain/snow sensor controllers.

• Convenient Indoor Monitoring and Control
• Self Powered, No AC Wiring or Batteries Required
• Fits Any Standard Single Gang Electrical Box
• Compatible with Leviton DecoraŽ/Hubbell StyleLine(tm) Cover Plates
• You Choose The Cover Plate Color and Material
• Smart "Manual On" Operates for One Delay Off Cycle
• Home Automation Control Interface

The unit consists of an electronic printed circuit board mounted securely to a steel mounting plate. The overall dimensions of the PM-DP are 4.1"(104) x 1.8"(45) x 0.9"(23). The unit weighs 2.5 ounces. The PM-DP fits into a standard single gang or multi gang electrical enclosure. Compatible self-threading mounting screws that fit both metal and plastic enclosures are included. The plate also has mounting holes for a rectangular "modular" cover plate, similar to the Leviton DecoraŽ or Hubbell StyleLine(tm) series. This allows the user to select a cover plate color and material that blends with the decor of the room.

Wiring is performed by installing a CS-1 remote control/monitor cable into the companion snow sensor. If not ordered with the sensor this cable may be ordered with the CDP-2. A shielded 5 conductor cable is then installed between the snow sensor and the PM-DP. All signals between the units are very low voltage so no conduit or similar protection of the interconnect cable is required. The individual leads of the interconnect cable are then installed into the rear terminal block of the PM-DP and the unit is ready for operation. The PM-DP does not require batteries or an AC power connection. It is actually powered by parasitic voltage "stolen" from the snow sensor. Peak power consumption is only 3.5 milliwatts. Operational temperature range for the electronic components is -40oC to +85oC
Therefore, the DP-PM can be installed indoors or outside with proper protection from the elements.

Place your order before 4:00 pm, (PST) and we get it out same day

ProMelt PM-DP Spec & Installation Guide

SunTouch 25 years Warranty

DS-2B Rain/Snow Sensor Controller

Futures:

Automatic Activation means Lower Deicing Costs
Reliable Rain and Snow Detection
Full 30A @ 240VAC Control
Field Strap for 100-120/200-240 VAC Operation
Replaceable Precipitation Sensor
Easy Installation, Full Access to Electronics
8 Different Functions, 1 Part Number
Adjustable Temperature Trigger Point
Adjustable Delay Off Cycle
Selectable Low Temperature Cutoff
Smart "Manual On" Operates for One Delay Off Cycle
High Power, Low Price!

PM-2B Specifications
Dimensions	4¾"(120) x 7"(178) x 2¾"(70)
Weight	2 Lbs. (0.9 Kg)
Operating Temperature	-40oF to +185oF (-40oC to +85oC)
Enclosure Rating	NEMA 3R
Supply Power	100-120VAC/200-240VAC Field Selectable 15W maximum
Trigger Temperature	34oF-44oF (1.1oC-6.6oC) Field Selectable
Delay Off (Sensor)	2 Minutes
Delay Off Controller)	30-90 Minutes Field Selectable
Load Contact Capacity	30A @ 240 VAC/100,000 operations minimum at full load
Monitor Contact Capacity	24 VDC/VAC 400mA 10W total

Wiring is performed by terminating your existing wiring to the pre-installed pigtails. The DS-2B is mounted by either attaching the mounting hub to a rigid 1/2" or 3/4" conduit or by installing screws through the four mounting tabs provided

The PM-2B can be powered from either a 100-120 VAC or 200-240 VAC 50/60Hz source. Peak power consumption is 15 watts. Voltage selection is performed by installing provided jumpers onto the printed circuit board. The unit provides a single 240VAC @ 30A normally open load contact set. This contact set is paralleled with a low power contact set to provide remote activation monitoring.

Not sure what and how many you need, we here to Help
Contact flooringsupplyshop.com by Phone 877-880-8453 (TILE) , Email, or Fax, or stop by our store with the layout of your room and we will give you complete list of what you need.

Click on our Flooring Calculator to calculate not just how many electrical floor heaters you need, you can also see how much it will cost you daily or yearly, and adjust your uses base on your electrical floor heating budget.

PM-B2 Controller Spec and Installation Manual

SunTouch 25 years Warranty

PM 224 Rain and Snow Sensor Controller

The PM-224 is an advanced low voltage version of the DS-2B. It is primarily designed for hydronic pavement snow melting applications and battery/solar powered railroad deice and lubrication control. The 24VAC/VDC supply means less expensive wiring, no requirement for conduit, and lower installation costs.

• Designed for Low Voltage Hydronic and Battery Powered Systems
• Automatic Activation means Lower Deicing Costs
• Reliable Rain and Snow Detection
• 24VAC/VDC Operation, Only 20 VA Required
• You Choose The Cover Plate Color and Material
• Full 30A @ 24VAC Control
• Replaceable Precipitation Sensor
• Easy Installation, Full Access to Electronics
• 8 Different Functions, 1 Part Number
• Adjustable Temperature Trigger Point
• Adjustable Delay Off Cycle, Selectable 30-90 Mins or 2-6 Hrs
• Exclusive Adjustable Sensitivity Control
• Selectable Low Temperature Cutoff
• Smart "Manual On" Operates for One Delay Off Cycle
• High Power, Low Price!

The unit is housed in a two gang PVC enclosure. The overall dimensions of the PM-224 are 4¾"(120) x 7"(178) x 2¾"(70). The unit weighs 2 pounds. The user may access all electronics by removing the four front cover screws.

Wiring is performed by terminating your existing wiring to the pre-installed pigtails. The PM-224 is mounted by either attaching the mounting hub to a rigid ½" or ¾" conduit or by installing screws through the four mounting tabs provided

The PM-224 can be powered from a 22-28VAC/VDC source. Peak power consumption is 15 VA at startup, 8.5 VA steady state triggered, 5 VA steady state untriggered. Power input is polarity protected for a DC supply. The unit provides a single 24VAC/30A or 24VDC/20A normally open load contact set. This contact set is paralleled with a low power contact set to provide remote control and activation monitoring. Operational temperature range is -40oC to +85oC.

The table below outlines the operating modes for the PM-224. Trigger Temperature (TT) is adjustable from 34oF-44oF using an on-board control. When ambient air temperature (AT) is below this trigger point precipitation is assumed to be snow or freezing rain. When above the trigger point, precipitation is assumed to be rain.

"Delay Off" refers to the internal drying cycle timer of the DS-224. The timer is used to allow the DS-224 to dry the heated surface through evaporation once precipitation has stopped. The drying cycle reduces the chance that moisture left behind by the melting process will refreeze into ice. This timer is restarted by each precipitation detection. Therefore, the DS-224 will continue to operate as long as precipitation and trigger temperature is detected, then for the "Delay Off" time once rain or snow stops. It is assumed that, when operating as a sensor, the DS-224 is supplying an activation signal to an external control system. All "sensor" modes provide a minimum 2 minute closure, reducing cycling of the external controller. The Delay Off cycle has been extended for hydronic applications and is determined by the Long Delay (LD) switch setting, DEL switch setting and the DEL adjustment. Delay Off is 30-90 minutes in non-LD "controller" mode and 2-6 hours in LD "controller" mode.

Place your order before 4:00 pm, (PST) and we get it out same day

PM-224 Spec and Installation Manual

SunTouch 25 years Warranty