Blanke Magnetic Tile Catch

Blanke Magnetic Catches are ideal for creating easy-to-remove panels for accessing plumbing and electrical equipment for bathrooms and hot tubs.

The panels are made from the same tile as the surrounding installation making them nearly invisible.

Can be applied irrespective of tile size and thickness, and adapts perfectly to the joint pattern.

The Blanke Magnetic Tile Catch set includes 4 magnets, and 4 mounting plates.

For more info click here

Blanke ULTRA-DRAIN - Single Sheets 6.5 sq ft

Ultradrain Drainage and uncoupling without a mud bed

This product sold by sheet of 6.5 sq ft - minimum order is 4 sheet or 26 sq ft. (no minimum for walk in customer)

Blanke ULTRA-DRAIN is the first drain mat system that can be installed without a thick mortar bed and that offers all the stress absorption properties of an uncoupling system.
The superior drainage properties of the Blanke ULTRA-DRAIN prevent freeze/thaw damage caused by the accumulation of moisture in exterior tile installations and help reduce unsightly efflorescence.
Although only 1/4" thick, the Blanke ULTRA-DRAIN provides superior compressive and tensile strength when compared to other drain mats and uncoupling systems.

Properties:
• Prevents freeze/thaw damage caused by moisture accumulation in exterior tile installations.
• Helps prevent unsightly efflorescence.
• Provides both superior drainage capacity and crack isolation properties.
• Install with thinset mortar or Blanke AQUA SEAL – no mud bed required.
• Use with Blanke AQUA SHIELD and accessories to waterproof deck.

Blanke ULTRA-DRAIN provides the ultimate drainage and uncoupling system for outdoor tile installations.
Unlike other drainage systems, the Blanke ULTRA-DRAIN does not require a thick mud bed and can be installed using thinset mortar or water proof adhesive.
This lightweight easy-to-install mat offers superior drain capabilities and all the stress absorption properties of an uncoupling system.

Installation:
In addition to being clean, dry, flat and load bearing, the substrate must be sloped a minimum of 1/4” per foot and waterproofed (If installation is not over occupied space, use Blanke AQUA SHIELD 100 for waterproofing).
Trowel a more liquid than normal mix of thinset mortar onto substrate.
Lay the Blanke ULTRA-DRAIN panels in a row so that the mesh overhang on the two sides of a panel cover the seams of the sides of adjacent panels without the overhang.
Subsequent rows of panels should be placed so that the seams running perpendicular to the previous row are offset a minimum of 3” from the seams running in the same direction in the previous row.
Use the flat side of a trowel or a vinyl roller to press the panel into the thinset ensuring that the fabric on the underside of the panel achieves full contact with the thinset and that there are no air bubbles.
Use the flat side of the trowel to key thinset into the voids on top of the Blanke ULTRA-DRAIN. Set tile using a notch trowel appropriate for the type of tile and traffic.
Blanke BALCON-Edge Protector with built in weep holes can be used to protect terrace or deck edge. (Read Blanke ULTRA-DRAIN Installation Instruction Blanke BALCONY SYSTEM prior to installing these products).
Movement joints need to be placed in the tile surface per industry standards and Tile Council of America guidelines.

Typical Applications:
Exterior tiled decks, terraces and balconies.

Suitable Substrates:
Plywood (EGP only – water proofed and sloped)
• 16” o.c. joist spacing, minimum subfloor thickness: 5/8”
• 19.2” o.c. joist spacing, minimum subfloor thickness: 3/4”
• 24” o.c. joist spacing, minimum subfloor thickness: double layer 3/4” + 3/8” panels.
Substrate deflection must not exceed L/360 for tile and L/720 for stone
Concrete (water proofed and sloped minimum of 1/4” per foot) Self-adhesive, non-heat treated bitumen based water-proofing products
Floor heating systems (consult Blanke installation instructions) Polyethylene waterproofing fabric such as Blanke AQUA SHIELD

Technical Data:

Top Mesh: Extruded twisted strands of highly alkali resistant glass heat welded to the lower layer of HDPE mesh.
Lower Mesh: Extruded twisted strands of alkali resistant high-density polyethylene (HDPE) forming two bottom layers of overlapping mesh with fleece fabric separating the layers.
Fabric: Polypropylene fleece
Thickness: approx. 6.3 mm (approx. 1/4 inch)
Weight: approx. 1.5 kg/m2 (approx. 4.9 ounces/sq. ft); 2 lbs. per panel; 30 lbs per carton.
Color: Fabric: white HDPE Mesh layers: light

Watch the Video part 1 - Watch the Video part 2

All about Blanke PerMat

How to Install Blanke PerMat

Blanke PERMAT 5 Years Limited Warranty

click here for more Information

Blanke ULTRA DRAIN Carton 97.5 sq ft

Ultradrain Drainage and uncoupling without a mud bed

Carton is 97.5 sq sheet - Size 24" x 38" - 15 Sheet per cartoon

Blanke ULTRA-DRAIN is the first drain mat system that can be installed without a thick mortar bed and that offers all the stress absorption properties of an uncoupling system.
The superior drainage properties of the Blanke ULTRA-DRAIN prevent freeze/thaw damage caused by the accumulation of moisture in exterior tile installations and help reduce unsightly efflorescence.
Although only 1/4” thick, the Blanke ULTRA-DRAIN provides superior compressive and tensile strength when compared to other drain mats and uncoupling systems.

Properties:
• Prevents freeze/thaw damage caused by moisture accumulation in exterior tile installations.
• Helps prevent unsightly efflorescence.
• Provides both superior drainage capacity and crack isolation properties.
• Install with thinset mortar or Blanke AQUA SEAL – no mud bed required.
• Use with Blanke AQUA SHIELD and accessories to waterproof deck.

Blanke ULTRA-DRAIN provides the ultimate drainage and uncoupling system for outdoor tile installations.
Unlike other drainage systems, the Blanke ULTRA-DRAIN does not require a thick mud bed and can be installed using thinset mortar or water proof adhesive.
This lightweight easy-to-install mat offers superior drain capabilities and all the stress absorption properties of an uncoupling system.

Installation:
In addition to being clean, dry, flat and load bearing, the substrate must be sloped a minimum of 1/4” per foot and waterproofed (If installation is not over occupied space, use Blanke AQUA SHIELD 100 for waterproofing).
Trowel a more liquid than normal mix of thinset mortar onto substrate.
Lay the Blanke ULTRA-DRAIN panels in a row so that the mesh overhang on the two sides of a panel cover the seams of the sides of adjacent panels without the overhang.
Subsequent rows of panels should be placed so that the seams running perpendicular to the previous row are offset a minimum of 3” from the seams running in the same direction in the previous row.
Use the flat side of a trowel or a vinyl roller to press the panel into the thinset ensuring that the fabric on the underside of the panel achieves full contact with the thinset and that there are no air bubbles.
Use the flat side of the trowel to key thinset into the voids on top of the Blanke ULTRA-DRAIN. Set tile using a notch trowel appropriate for the type of tile and traffic.
Blanke BALCON-Edge Protector with built in weep holes can be used to protect terrace or deck edge. (Read Blanke ULTRA-DRAIN Installation Instruction Blanke BALCONY SYSTEM prior to installing these products).
Movement joints need to be placed in the tile surface per industry standards and Tile Council of America guidelines.

Typical Applications:
Exterior tiled decks, terraces and balconies.

Suitable Substrates:
Plywood (EGP only – water proofed and sloped)
• 16” o.c. joist spacing, minimum subfloor thickness: 5/8”
• 19.2” o.c. joist spacing, minimum subfloor thickness: 3/4”
• 24” o.c. joist spacing, minimum subfloor thickness: double layer 3/4” + 3/8” panels.
Substrate deflection must not exceed L/360 for tile and L/720 for stone
Concrete (water proofed and sloped minimum of 1/4” per foot) Self-adhesive, non-heat treated bitumen based water-proofing products
Floor heating systems (consult Blanke installation instructions) Polyethylene waterproofing fabric such as Blanke AQUA SHIELD

Technical Data:

Top Mesh: Extruded twisted strands of highly alkali resistant glass heat welded to the lower layer of HDPE mesh.
Lower Mesh: Extruded twisted strands of alkali resistant high-density polyethylene (HDPE) forming two bottom layers of overlapping mesh with fleece fabric separating the layers.
Fabric: Polypropylene fleece
Thickness: approx. 6.3 mm (approx. 1/4 inch)
Weight: approx. 1.5 kg/m2 (approx. 4.9 ounces/sq. ft); 2 lbs. per panel; 30 lbs per carton.
Color: Fabric: white HDPE Mesh layers: light

click here for Installation Instructions

Blanke PERMAT - 6.5 sq ft per sheet

Permat: the deflection reducing Uncoupling Underlayment

This product sold by sheet of 6.5 sq ft - minimum order is 4 sheet or 26 sq ft. (no minimum for walk in customer)

Blanke PERMAT is an innovative uncoupling underlayment that offers all the labor saving benefits of the old plastic roll systems.
Blanke PERMAT also adds support to wood substrates thereby reducing deflection and provides greater compression and tensile strength than plastic roll products. The Blanke PERMAT is stable to walk on during installation and does not require additional curing time when installing porcelain with latex modified thinset.

• Adds the extra substrate support for stone floor installation (max L/720 for stone vs L/360 for tile)
• Approved for ceramic tile installation over layer of 3/4" plywood on 24" o. c. joist spacing.
• 10 year replacement warranty against problems caused by excess deflection -- only warranty of its kind in the industry. (see permat warranty for details).

Properties:

• Strengthens wood substrates thereby reducing deflection
• Superior compressive strength.
• Superior tensile strength.
• Crack isolation properties (uncoupling)
• Superior resistance to delaminating during installation.
• No extended cure time for latex modified thinset mortars under porcelain tile.
• Lightweight; easy to install
• Self-seaming panels prevent substrate movement stress form transmitting to tiled surface.

Blanke PERMAT is an innovative uncoupling underlayment that adds support to wood substrates thereby reducing deflection and provides superior compression and tensile strength when compared to plastic roll and cement board products. Installed with thinset mortar, the Blanke PERMAT panels feature a mesh overhang to connect adjacent panels thereby eliminating seams that can transmit substrate movement stress to the tiled surface.
Tile can be applied immediately after installing the Blanke PERMAT.

Installation:
Substrate must be clean, dry, flat and load bearing. Trowel a more liquid than normal mix of thinset mortar onto substrate.
Lay the Blanke PERMAT panels in a row so that the mesh overhang on the two sides of a panel cover the seams of the sides of adjacent panels without the overhang. Subsequent rows of panels should be placed so that the seams running perpendicular to the previous row are offset a minimum of 3” from the seams running in the same direction in the previous row.
Use the flat side of a trowel or a vinyl roller to press the panel into the thinset ensuring that the fabric on the underside of the panel achieves full contact with the thinset and that there are no air bubbles.
Use the flat side of the trowel to key thinset into the voids on top of the Blanke PERMAT.
Set tile using a notch trowel appropriate for the type of tile and traffic. (Read Blanke PERMAT Installation Instruction prior to installing this product).
Movement joints are required in the tile surface per industry standards.

Typical Applications:
Blanke PERMAT is an ideal alternative to backer board underlayment used in interior residential applications over wood substrates where excess deflection may be an issue and in commercial applications on concrete where stress cracks can be a problem.
Blanke PERMAT is ideally suited for new home construction where demanding installation schedules cause traffic to cross on the underlayment prior to tile installation an

Suitable Substrates:
Wood substrates – stone and tile (including large format) Plywood EGP and OSB
16” o.c. joist spacing, minimum subfloor thickness: 5/8”
19.2” o.c. joist spacing, minimum subfloor thickness: 3/4”
Wood substrates – tile only (no larger than16”x16”)
24" o.c. joist spacing, minimum subfloor thickness: 3/4" (subject to maximum joist span restrictions)
Concrete substrates
Substrates covered with stone, tile and vinyl (consult thinset manufacturer instructions)
Floor heating systems (consult Blanke installation instructions)

Technical Data:

Top Mesh: Extruded twisted strands of highly alkali resistant glass fiber, heat welded to the lower layer of HDPE mesh.
Bottom Mesh: Extruded twisted strands of alkali resistant high-density polyethylene (HDPE).
Fabric material: Polypropylene fleece
Thickness: approx. 3.3 mm (nominal 1/8 inch)
Weight: approx. 0.8 kg/m2 (approx. 2.6 ounces/sq. ft): 1.06 lbs. per - panel: 31.8 lbs. per carton
Color: Fabric: white HDPE Mesh: light-blue Top Mesh: dark blue

All about Blanke PerMat

How to Install Blanke PerMat

Blanke PERMAT 5 Years Limited Warranty

click here for more Information

Blanke PERMAT - Carton 195 sq ft

Permat: the deflection reducing Uncoupling Underlayment

Blanke PERMAT is an innovative uncoupling underlayment that offers all the labor saving benefits of the old plastic roll systems.
Blanke PERMAT also adds support to wood substrates thereby reducing deflection and provides greater compression and tensile strength than plastic roll products. The Blanke PERMAT is stable to walk on during installation and does not require additional curing time when installing porcelain with latex modified thinset.

• Adds the extra substrate support for stone floor installation (max L/720 for stone vs L/360 for tile)
• Approved for ceramic tile installation over layer of 3/4" plywood on 24" o. c. joist spacing.
• 10 year replacement warranty against problems caused by excess deflection -- only warranty of its kind in the industry (see permat warranty for details).

Properties:

• Superior compressive strength.
• Strengthens wood substrates thereby reducing deflection
• Superior compressive strength.
• Superior tensile strength.
• Crack isolation properties (uncoupling)
• Superior resistance to delaminating during installation.
• No extended cure time for latex modified thinset mortars under porcelain tile.
• Lightweight; easy to install
• Self-seaming panels prevent substrate movement stress form transmitting to tiled surface.

Blanke PERMAT is an innovative uncoupling underlayment that adds support to wood substrates thereby reducing deflection and provides superior compression and tensile strength when compared to plastic roll and cement board products. Installed with thinset mortar, the Blanke PERMAT panels feature a mesh overhang to connect adjacent panels thereby eliminating seams that can transmit substrate movement stress to the tiled surface.
Tile can be applied immediately after installing the Blanke PERMAT.

Installation:
Substrate must be clean, dry, flat and load bearing. Trowel a more liquid than normal mix of thinset mortar onto substrate.
Lay the Blanke PERMAT panels in a row so that the mesh overhang on the two sides of a panel cover the seams of the sides of adjacent panels without the overhang. Subsequent rows of panels should be placed so that the seams running perpendicular to the previous row are offset a minimum of 3” from the seams running in the same direction in the previous row.
Use the flat side of a trowel or a vinyl roller to press the panel into the thinset ensuring that the fabric on the underside of the panel achieves full contact with the thinset and that there are no air bubbles.
Use the flat side of the trowel to key thinset into the voids on top of the Blanke PERMAT.
Set tile using a notch trowel appropriate for the type of tile and traffic. (Read Blanke PERMAT Installation Instruction prior to installing this product).
Movement joints are required in the tile surface per industry standards.

Typical Applications:
Blanke PERMAT is an ideal alternative to backer board underlayment used in interior residential applications over wood substrates where excess deflection may be an issue and in commercial applications on concrete where stress cracks can be a problem.
Blanke PERMAT is ideally suited for new home construction where demanding installation schedules cause traffic to cross on the underlayment prior to tile installation

Suitable Substrates:
Wood substrates – stone and tile (including large format) Plywood EGP and OSB
16” o.c. joist spacing, minimum subfloor thickness: 5/8”
19.2” o.c. joist spacing, minimum subfloor thickness: 3/4”
Wood substrates – tile only (no larger than16”x16”)
24" o.c. joist spacing, minimum subfloor thickness: 3/4" (subject to maximum joist span restrictions)
Concrete substrates
Substrates covered with stone, tile and vinyl (consult thinset manufacturer instructions)
Floor heating systems (consult Blanke installation instructions)

Technical Data:

Top Mesh: Extruded twisted strands of highly alkali resistant glass fiber, heat welded to the lower layer of HDPE mesh.
Bottom Mesh: Extruded twisted strands of alkali resistant high-density polyethylene (HDPE).
Fabric material: Polypropylene fleece
Thickness: approx. 3.3 mm (nominal 1/8 inch)
Weight: approx. 0.8 kg/m2 (approx. 2.6 ounces/sq. ft): 1.06 lbs. per - panel: 31.8 lbs. per carton
Color: Fabric: white HDPE Mesh: light-blue Top Mesh: dark blue

Watch the Video part 1 - Watch the Video part 2

All about Blanke PerMat

How to Install Blanke PerMat

Blanke PERMAT 5 Year Limited Warranty

click here for more Information

Blanke UNI-Mat PRO - Cut

UNI-Mat Pro the Universal uncoupling underlayment.

This product sold by linear run, every feet run equal to 3.3 sq feet.

Select how many unit (feet) you need.

Blanke UNI-Mat PRO and Schluter Ditra are similar underlayment systems with some striking differences.

Click here to see Why Blanke UNI-Mat PRO and not Schluter Ditra

Properties:
• Lightweight, labor saving
• Crack isolation (uncoupling)
• Equalized substrate vapor pressure
• Absorption of stress from lateral substrate movement
• Waterproof function

The Blanke UNI-Mat PRO is a durable, lightweight, easy to install underlayment system that saves installation time and labor costs when compared to heavier, more traditional alternatives such as cement board.
The unique circular column design of the polyethylene sheeting and the fleece scrim underside give the Blanke UNI-Mat PRO superior absorption properties for stress caused by multidirectional lateral substrate movement.
These same properties make the Blanke UNI-Mat PRO a suitable system for bridging tension cracks in cement substrates.
The voids on the underside of the mat around the circular columns neutralize pressure caused by substrate moisture vaporization.
The top mesh provides a more tenacious bond with the tile and a stable working surface.

Installation:
Substrate must be clean flat and load bearing. Trowel a more liquid than normal mix of thinset mortar onto the substrate.
Using a vinyl roller or flat side of the trowel, press the cut sections into the thinset so that the fabric on the underside absorbs the thinset and any air bubbles are eliminated. Using the flat side of the trowel, fill in the cavities on the surface of the mat with a normal mix of thinset. Set tile using a normal mix of thinset and a trowel appropriate for the type of tile and traffic exposure. (Read the detailed Blanke UNI-Mat PRO Installation Instructions prior to installing this product).

Typical Applications:
Blanke UNI-Mat PRO is an ideal alternative to backer board underlayment used in interior residential and light commercial tiled floor applications over wood substrates.
The Blanke UNI-Mat PRO can also be used as an underlayment for tile applications on concrete where vapor transmission and stress cracks can be a problem.

Suitable Substrates (for ceramic tile):
Plywood and OSB (Exterior Glue only)
• 16” o.c. joist spacing, minimum subfloor thickness: 5/8”
• 19.2” o.c. joist spacing, minimum subfloor thickness: 3/4”
• 24” o.c. joist spacing, minimum subfloor thickness: double layer 3/4” + 3/8” panels Substrate deflection must not exceed L/360 for tile a and L/720 for stone

Concrete subfloors (including those with stress cracks and those cured less than 28 days) Substrates covered with stone, tile and vinyl (consult thinset manufacturer instructions)
Floor heating systems (consult Blanke installation instructions)

Technical Data:

Thickness: approx. 4 mm (approx. 1/8 inch)
Weight: approx. 550 g/m2 (approx. 1.8 ounces/sq. ft.); 36.3 lbs per roll
Water resistance: waterproof
Fabric material: Polypropylene fleece
Mat material: High-density polyethylene (HDPE) with circular cavities
Mesh: High-density polyethylene (twisted strands) heat bonded to plastic mat.
Color: Plastic Mat: blue Fabric: white

Watch the Video part 1 - Watch the Video part 2

How to Install Blanke Uni Mat Pro

Blanke UNI-Mat PRO - Roll 323 sq ft

UNI-Mat Pro: the Universal uncoupling underlayment.

Blanke UNI-Mat PRO and Schluter Ditra are two similar underlayment systems with some striking differences.

Click here to see Why Blanke UNI-Mat PRO and not Schluter Ditra

Properties:
• Lightweight, labor saving
• Crack isolation (uncoupling)
• Equalized substrate vapor pressure
• Absorption of stress from lateral substrate movement
• Waterproof function

The Blanke UNI-Mat PRO is a durable, lightweight, easy to install underlayment system that saves installation time and labor costs when compared to heavier, more traditional alternatives such as cement board.
The unique circular column design of the polyethylene sheeting and the fleece scrim underside give the Blanke UNI-Mat PRO superior absorption properties for stress caused by multidirectional lateral substrate movement.
These same properties make the Blanke UNI-Mat PRO a suitable system for bridging tension cracks in cement substrates.
The voids on the underside of the mat abound the circular columns neutralize pressure caused by substrate moisture vaporization.
The top mesh provides a more tenacious bond with the tile and a stable working surface.

Installation:
Substrate must be clean flat and load bearing. Trowel a more liquid than normal mix of thinset mortar onto the substrate.
Using a vinyl roller or flat side of the trowel, press the cut sections into the thinset so that the fabric on the underside absorbs the thinset and any air bubbles are eliminated. Using the flat side of the trowel, fill in the cavities on the surface of the mat with a normal mix of thinset. Set tile using a normal mix of thinset and a trowel appropriate for the type of tile and traffic exposure. (Read the detailed Blanke UNI-Mat PRO Installation Instructions prior to installing this product).

Typical Applications:
Blanke UNI-Mat PRO is an ideal alternative to backer board underlayment used in interior residential and light commercial tiled floor applications over wood substrates.
The Blanke UNI-Mat PRO can also be used as an underlayment for tile applications on concrete where vapor transmission and stress cracks can be a problem.

Suitable Substrates (for ceramic tile):
Plywood and OSB (Exterior Glue only)
• 16” o.c. joist spacing, minimum subfloor thickness: 5/8”
• 19.2” o.c. joist spacing, minimum subfloor thickness: 3/4”
• 24” o.c. joist spacing, minimum subfloor thickness: double layer 3/4” + 3/8” panels Substrate deflection must not exceed L/360 for tile a and L/720 for stone

Concrete subfloors (including those with stress cracks and those cured less than 28 days) Substrates covered with stone, tile and vinyl (consult thinset manufacturer instructions)
Floor heating systems (consult Blanke installation instructions)

Technical Data:

Thickness: approx. 4 mm (approx. 1/8 inch)
Weight: approx. 550 g/m2 (approx. 1.8 ounces/sq. ft.); 36.3 lbs per roll
Water resistance: waterproof
Fabric material: Polypropylene fleece
Mat material: High-density polyethylene (HDPE) with circular cavities
Mesh: High-density polyethylene (twisted strands) heat bonded to plastic mat.
Color: Plastic Mat: blue Fabric: white

Watch the Video part 1 - Watch the Video part 2

How to Install Blanke Uni Mat Pro

Blanke AQUA SEAL EZA

V-notched nozzle

Blanke Aqua Seal EZA is an applicator head that attaches directly to the Blanke Aqua Seal tube for ease of use when installing and seaming Blanke Aqua Seal waterproofing fabric.

For example, we recommend using the Blanke DIBA-COLL ZSD (V-notched nozzle) for adhereing the Blanke DIBA.

Blanke AQUA SHIELD - Inside Corner

Inside corner size = 12.5"

Aqua Shield Waterproofing Membrane Inside Corners are pre-cut and preformed for easy fitment. Aqua Shild sheets alone not enough to ensure a water tight shower assembly. Aqua Shield Inside Corners help you seal the corners of your shower system before installing your tile.

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SHIELD - Outside Corner

Outside corner size = 12.5"

Aqua Shield Waterproofing Membrane Outside Corners are pre-cut and preformed for easy fitment. Aqua Shild sheets alone not enough to ensure a water tight shower assembly. Aqua Shield Outside Corners help you seal the corners of your shower system before installing your tile.

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SHIELD - SP

Diameter of hole = 13/15"

Length 4" x 4"

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SHIELD - LP

Diameter of hole = 6 9/14"

Length 17 2/3" x 17 2/3"

The Floor Drain Seal allows you to easily install the Aqua Shield Waterproofing Membrane around your floor drain without having to make any additional cuts.

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SHIELD - 5 inch - CUT PER ORDER

This product sold by linear run.

Select how many unit (feet) you need.

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SHIELD - 5 inch

Roll of 5" x 98.4'

Use Aqua Shield Waterproofing Seam strips over your Membrane Seams

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD's engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SHIELD - Cut per order

This product sold by linear run, every feet run equal to 3.3 sq feet.

Select how many unit (feet) you need.

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD's engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SHIELD

Roll of 323 sq feet 3' 3" x 98'5"

Blanke AQUA SHIELD is a waterproofing fabric that can be applied with thinset to most surfaces that are dry, flat and structurally sound. Tile can be installed directly on fabric without the cure time required for liquid applied products. Blanke AQUA SHIELD provides a vapor barrier that makes it ideal for steam rooms. The high tensile strength of the Blanke AQUA SHIELD ensures long lasting protection from moisture penetration in continuous wet areas such as shower stalls and bathrooms. In addition to waterproofing, the Blanke AQUA SHIELD's engineered blend of fibers also provide exceptional resistance to mold build-up; break-down from strong chemicals; and UV destabilization. A wide range of convenient accessories is available such as Blanke AQUA FLEX for taping movement joints; Blanke AQUA SA, a self-adhesive tape for quick and convenient taping of seams; and preformed corners.

Application.

Check substrate to ensure that it is dry, even and sound. Apply a setting adhesive suitable for the application to the wall or floor substrate with a 4 mm notched trowel. Apply the adhesive on an area approximately 3/8" wider than the Aqua Shield fabric. Cut the fabric to the desired length and place on the substrate in the same manner as when hanging wall paper and smooth out with a wall paper brush (tampico brush). Use a wide flat trowel to carefully embed the fabric into the adhesive ensuring there are no air pockets. Allow at least a 1/4" fabric overlap. The tiles can then be installed immediately onto the Aqua Shield in the normal manner. .

Installation:

1. The surface must be clean, even and load bearing. The substrate must be sufficiently free of moisture. (Use a moisture meter if unsure of moisture content).

2. Porous surfaces like concrete may have to be coated with a suitable primer.

3. General Installation Procedures: All of the detail areas, such as around plumbing pipes, wall-to-floor transitions, wall-to-wall connections (including corners), around drains and movement joints if present, must be sealed up first using convenient Blanke AQUA SHIELD accessories (pipe surrounds, preformed corners, self-adhesive tapes, etc.) After this step is completed, the wall and floor surfaces need to be sealed up using the larger rolls. The ceramic tile can then be installed immediately.

4. Detailed Installation - Plumbing Pipes: Use a 1/4" x 3/16" V - notched trowel to apply the thinset to the substrate around the pipe. Press the Blanke AQUA SHIELD SP or LP around the pipe and against the wall with a trowel. Use the trowel to scrape off excess thinset. Use Blanke AQUA SEAL water proofing adhesive to seal the edges of Blanke AQUA SHIELD SP/LP to the area around the pipe or plumbing fixture.

Blanke AQUA SEAL

1 cartridge = 10.5 ounce

Blanke AQUA SEAL is a multi-purpose water proofing polymer adhesive that can be used to waterproof and seal the overlapping seams of Blanke AQUA SHIELD.
It can also be used to installed the Blanke•ULTRA DRAIN to substrates with a water proofing layer that does not accept thinset.

The Blanke AQUA SEAL is free from solvent, isocyanates and silicone.